Show simple item record

Files in this item

FilesSizeFormatView

There are no files associated with this item.

Item metadata

dc.contributor.advisorIrvine, John T. S.
dc.contributor.authorPrice, Robert
dc.coverage.spatialiii, 290 p.en_US
dc.date.accessioned2018-09-12T11:28:39Z
dc.date.available2018-09-12T11:28:39Z
dc.date.issued2018-11-06
dc.identifier.urihttps://hdl.handle.net/10023/16018
dc.description.abstractSolid Oxide Fuel Cells (SOFC) are electrochemical energy conversion devices which allow fuel gases, e.g. hydrogen or natural gas, to be converted to electricity and heat at much high efficiencies than combustion-based energy conversion technologies. SOFC are particularly suited to employment in stationary energy conversion applications, e.g. micro-combined heat and power (µ-CHP) and base load, which are certain to play a large role in worldwide decentralisation of power distribution and supply over the coming decades. Use of high-temperature SOFC technology within these systems is also a vital requirement in order to utilise fuel gases which are readily available in different areas of the world. Unfortunately, the limiting factor to the long-term commercialisation of SOFC systems is the redox instability, coking intolerance and sulphur poisoning of the state-of-the-art Ni-based cermet composite anode material. This research explores the ‘powder to power’ development of alternative SOFC anode catalyst systems by impregnation of an A-site deficient La₀.₂₀Sr₀.₂₅Ca₀.₄₅TiO₃ (LSCT[sub](A-)) anode ‘backbone’ microstructure with coatings of ceria-based oxide ion conductors and metallic electrocatalyst particles, in order to create a SOFC anode which exhibits high redox stability, tolerance to sulphur poisoning and low voltage degradation rates under operating conditions. A 75 weight percent (wt. %) solids loading LSCT[sub](A-) ink, exhibiting ideal properties for screen printing of thick-film SOFC anode layers, was screen printed with 325 and 230 mesh counts (per inch) screens onto electrolyte supports. Sintering of anode layers between 1250 °C and 1350 °C for 1 to 2 hours indicated that microstructures printed with the 230 mesh screen provided a higher porosity and improved grain connectivity than those printed with the 325 mesh screen. Sintering anode layers at 1350 °C for 2 hours provided an anode microstructure with an advantageous combination of lateral grain connectivity and porosity, giving rise to an ‘effective’ electrical conductivity of 17.5 S cm⁻¹ at 850 °C. Impregnation of this optimised LSCT[sub](A-) anode scaffold with 13-16 wt. % (of the anode mass) Ce₀.₈₀Gd₀.₂₀O₁.₉₀ (CGO) and either Ni (5 wt. %), Pd, Pt, Rh or Ru (2-3 wt. %) and integration into SOFC resulted in achievement of Area Specific Resistances (ASR) of as low as 0.39 Ω cm⁻², using thick (160 µm) 6ScSZ electrolytes. Durability testing of SOFC with Ni/CGO, Ni/CeO₂, Pt/CGO and Rh/CGO impregnated LSCT[sub](A-) anodes was subsequently carried out in industrial button cell test rigs at HEXIS AG, Winterthur, Switzerland. Both Ni/CGO and Pt/CGO cells showed unacceptable levels of degradation (14.9% and 13.4%, respectively) during a ~960 hour period of operation, including redox/thermo/thermoredox cycling treatments. Significantly, by exchanging the CGO component for the CeO₂ component in the SOFC containing Ni, the degradation over the same time period was almost halved. Most importantly, galvanostatic operation of the SOFC with a Rh/CGO impregnated anode for >3000 hours (without cycling treatments) resulted in an average voltage degradation rate of <1.9% kh⁻¹ which, to the author’s knowledge, has not previously been reported for an alternative, SrTiO₃-based anode material. Finally, transfer of the Rh/CGO impregnated LSCT[sub](A-) anode to industrial short stack (5 cells) scale at HEXIS AG revealed that operation in relevant conditions, with low gas flow rates, resulted in accelerated degradation of the Rh/CGO anode. During a 1451 hour period of galvanostatic operation, with redox cycles and overload treatments, a voltage degradation of 19.2% was observed. Redox cycling was noted to briefly recover performance of the stack before rapidly degrading back to the pre-redox cycling performance, though redox cycling does not affect this anode detrimentally. Instead, a more severe, underlying degradation mechanism, most likely caused by instability and agglomeration of Rh nanoparticles under operating conditions, is responsible for this observed degradation. Furthermore, exposure of the SOFC to fuel utilisations of >100% (overloading) had little effect on the Rh/CGO co-impregnated LSCT[sub](A-) anodes, giving a direct advantage over the standard HEXIS SOFC. Finally, elevated ohmic resistances caused by imperfect contacting with the Ni-based current collector materials highlighted that a new method of current collection must be developed for use with these anode materials.en_US
dc.language.isoenen_US
dc.publisherUniversity of St Andrews
dc.subjectSolid oxide fuel cellen_US
dc.subjectStrontium titanateen_US
dc.subjectCatalyst impregnationen_US
dc.subjectDurability testingen_US
dc.subjectShort stack testingen_US
dc.subjectElectrolyte-supported SOFCen_US
dc.subject.lccTK2933.S65P8
dc.subject.lcshSolid oxide fuel cells--Materialsen
dc.subject.lcshAnodes--Materialsen
dc.subject.lcshStrontium titanateen
dc.titleMetal/metal oxide co-impregnated lanthanum strontium calcium titanate anodes for solid oxide fuel cellsen_US
dc.typeThesisen_US
dc.contributor.sponsorUniversity of St Andrewsen_US
dc.contributor.sponsorHEXIS AGen_US
dc.type.qualificationlevelDoctoralen_US
dc.type.qualificationnamePhD Doctor of Philosophyen_US
dc.publisher.institutionThe University of St Andrewsen_US
dc.rights.embargodate2019-07-30
dc.rights.embargoreasonThesis restricted in accordance with University regulations. Print and electronic copy restricted until 30th July 2019en


This item appears in the following Collection(s)

Show simple item record